How To Install Ventilation Fan On Window

On This Page:

1. How to Install an Attic Gable Fan
1. Replacing
2. Roof Vent Exhaust Installation
3. Best Place to Install
4. How to Install a Whole Firm Fan
5. DIY vs. Hiring a Pro

Attic Gable-Mounted Fan Installation

Gable-mounted installations are the simplest to perform, particularly if in that location is already a gable vent in place. Yous or your installer can perform the post-obit steps from the interior without having to work from the exterior. Be sure to consult the fan's owner's transmission for measurements and details.

1. Set the opening.
1. If an accurately sized gable vent already exists, continue to footstep ii.
2. If the current gable vent is too small-scale for the fan:
• Remove the under-sized shutter and utilize your new shutter to mark the edges for cutting.
• Articulate obstructions like framing and lap siding.
• Cut the new edges using a sabre saw.
• Secure new shutter with screws and apply caulk to seal the new perimeter.
2. Create a mounting console using plywood.
• Make sure the plywood volition fit the framing effectually the shutter.
• Your fan should come up with a cutout to mark the hole size for the fan. Use this guide to brand your hole in the plywood, then cut with a sabre saw.
• Center and set up the fan in the plywood, and screw the mounting subclass to the plywood.
3. Secure the fan to the gable wall.
• Middle the assembly behind the shutter and secure to the framing with nails.
4. Attach the included thermostat to a corner of the plywood mountain.
5. Wire the fan.
• Double-check that the power to the circuit you'll be connecting to is off.
• Connect the thermostat to the existing or designated circuit using an electric cablevision, connecting the correct circuit wires in both the thermostat and the circuit. Be sure to secure the cablevision using staples, so that it isn't running loosely through the attic.

Notation: For wiring, information technology'south best to hire an electrician. These pros will know and understand your local codes and voltage/amp requirements.

Ready to start your Attic or Whole House Fan Installation?

Notice Pros

Return to Acme

Replacing an Existing Fan

The cost of attic fan replacement is typically about $600 when y'all rent a professional. Replacement is necessary if the major elements of the fan fails. Replacing the motor will sometimes be sufficient and will merely cost effectually $200 for labor. In the example of total failure, your pro will perform the following steps.

1. Cut off the power supply.
2. Disconnect the wiring to the thermostat.
3. Detach the existing fan unit.
4. Attach the new fan (resize the hole to fit, if necessary).
5. Adhere and wire the new thermostat.

Return to Top

Roof Vent Exhaust Installation

When it comes to installing a fan in your roof, you volition need to work from both the inside and the outside. It is all-time to rent a roofing professional, as this type of work is dangerous and the proper treatment of covering and shingles is vital to leak prevention. If you practice DIY, use proper condom precautions, especially when handling electricity.

Keep in listen that roof vents should exist installed almost the ridge, peak or highest signal of the roof for optimum functioning. Likewise, regardless of your aesthetic preferences or whatever future plans you may take, you must follow proper procedure with lifting and replacing the shingles and flashing. Otherwise, you take chances leaks and water impairment.

1. Marking your centre.
• Measure around twenty inches down from the ridge and mark a center between the joists.
• Drive a dowel or nail as a marking through this eye, to show eye on the roof.
2. Cutting and remove immediate shingles.
• On roof, marking a circle around the dowel which matches the measurements needed for the fan'south flashing. This circumvolve will be wider than the circle you volition cut.
• Cut the measured circumvolve in the shingles using a utility knife and remove surrounding shingles temporarily.
3. Cut your airway.
• Mark a circle on the roof which will fit between the joist (practise not cutting your joists!).
• Cut this hole through the roof.
4. Install the vent.
• Secure the vent to the roof using roofing cement effectually the edge of the circle, applied directly to the roof.
• Secure fan with screws.
5. Seal the flashing.
• Apply caulk to the edges of the flashing to block out moisture.
• Replace and secure shingles.
6. Wire the fan.
• Perform any necessary wiring as described for gable-mounted fans above. This will not be necessary for solar, and some electrical fans come with simple plugs rather than wires.

Return to Acme

Where Should You Install Your Attic Ventilation Fan?

The benefits of gable and roof ventilation fans are relatively similar. Where you install your unit is upwards to aesthetic preference and budget.

Roof

• May come at a greater cost, considering that shingles must be moved and a pigsty created.
• Requires work from the outside, on the roof.
• With be visible on the roof and may not meet preferred aesthetics.

Gable

• May be more cost-effective if you already take a gable vent in place.
• May exist closer to an bachelor outlet.
• Does not crave work from outside, which makes for easier installation.

Set up to start your Attic or Whole House Fan Installation?

Find Pros

Return to Top

Whole House Fan Installation

Installing this system is a job for a pro. The process requires measurements, wiring and the cosmos of new vents. Improper installation can result in backdrafts, pulling air from your furnace, water heater, or gas appliances. Without plenty ventilation, this can let dangerous combustion toxins like carbon monoxide into the living space.

A licensed, experienced professional volition put in a tight-sealing wintertime cover and provide an access door, so the homeowner can switch betwixt heating and cooling methods easily. The HVAC service professional will also summate attic ventilation requirements to maximize cooling and energy efficiency.

A professional will perform the following steps for the fan itself, not including the installation of added ventilation where necessary:

1. Set the framing.
• Remove plywood and insulation from installation surface area, which should ideally exist in a central hallway. Whole house fans are sized to fit betwixt the joists of your attic.
• Install two 2 x 10 boards as a frame for the fan between joists. Be certain to exit a little bit of "wiggle room" for the fan. Secure with nails.
• Re-install plywood and cut a square along your framing both in the plywood and the ceiling.
2. Insulate and atmospheric condition-strip.
• Spray insulation in the gaps betwixt attic and ceiling.
• Utilise weather-stripping to fan where it volition rest on the plywood.
3. Install the fan.
• Prepare fan in the frame and secure with screws.
• Secure the grill to the hallway side of the installation.
4. Connect to an electrical outlet.
• You may demand to take a designated outlet installed if one is not available and in range.

Render to Top

DIY Fans vs. Hiring a Pro

Professional attic fan installation costs less than $600, on average. Labor is a pocket-sized fraction of the total, which makes hiring a pro an affordable and worthwhile option. At that cost, you are receiving a quality installation that is upwardly-to-code every bit far equally electric, and which performs at optimum capacity. You will be properly informed and your installer will be able to help you find the best equipment for your needs. A pro will be able to quickly execute the piece of work in a single twenty-four hours. DIY is not recommended for any electrical, roofing or solar piece of work.

Gear up to start your Cranium or Whole Business firm Fan Installation?

Observe Pros

Return to Top

Source: https://homeadvisor.com/r/how-to-install-attic-whole-house-fan/

Posted by: andersonpromple.blogspot.com

Share this post